View HS-7238_5034425.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HS-7238
Intel(R) Pentium(R) 4 processor PCI-ISA Bus Single Board Computer
*533MHz FSB*Mini PCI*DDR* *DVI-I/CRT*Dual LAN*Wireless LAN* *Audio*ATA/33/66/100*USB2.0* *WDT*H/W Monitor*
Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s). This manual is copyrighted and BOSER Technology Co., Ltd. reserves all documentation rights. Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording)
of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. BOSER Technology Co., Ltd. reserves the right to change or improve the contents of this document without due notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does it make any commitment to update the information contained herein.
Trademarks Trademarks
BOSER is a registered trademark of BOSER Technology Co., Ltd. ISB is a registered trademark of BOSER Technology Co., Ltd. Intel is a registered trademark of Intel Corporation. Award is a registered trademark of Award Software, Inc. AWARD is a registered trademark of AWARD Software, Inc. All other trademarks, products and or product names mentioned herein are mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners.
(c) Copyright 2007 BOSER Technology Co., Ltd. All Rights Reserved. Edition 1.4, March 21, 2007
Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features ....................................................................... 2 1.2 Specifications ........................................................................ 3 1.3 Board Dimensions................................................................. 4
Chapter 2 Chapter 3
3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21
Unpacking ..................................................5 Hardware Installation ..............................7
2.1 Opening the Delivery Package............................................. 5 2.2 Inspection............................................................................... 5 Before Installation ................................................................. 7 Board Layout ......................................................................... 8 Jumper List ............................................................................ 9 Connector List ....................................................................... 9 Configuring the CPU ........................................................... 10 Heat Sink Installation...............................................................................................10 System Memory ................................................................... 11 VGA Controller .................................................................... 11 PCI E-IDE Drive Connector................................................. 12 Floppy Disk Drive Connector ............................................. 13 Serial Port Connectors ....................................................... 13 Parallel Port.......................................................................... 14 Ethernet Connector............................................................. 15 USB Connector.................................................................... 15 CMOS Data Clear................................................................. 16 Power and Fan Connectors................................................ 16 Keyboard/Mouse Connectors ............................................ 17 System Front Panel Control ............................................... 18 Speaker................................................................................. 18 Watchdog Timer .................................................................. 19 Audio Connectors ............................................................... 20 Mini PCI Connector ............................................................. 22
Chapter 4
4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 5.1 5.2 5.3 5.4 5.5
Award BIOS Setup ................................. 23
Starting Setup...................................................................... 23 Using Setup ......................................................................... 24 Main Menu............................................................................ 25 Standard CMOS Features................................................... 26 Advanced BIOS Features ................................................... 27 Advanced Chipset Features............................................... 28 Integrated Peripherals ........................................................ 29 Power Management Setup ................................................. 30 PnP/PCI Configurations...................................................... 31 PC Health Status ................................................................. 32 Frequency/Voltage Control ................................................ 32
Chapter 5
Software Utilities..................................... 33
IDE Driver Installation ......................................................... 33 VGA Driver Installation ....................................................... 37 LAN Driver Installation........................................................ 46 Audio Driver Installation..................................................... 57 USB2.0 Driver Installation .................................................. 59
Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body. Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the product to ensure harmlessly discharge any static electricity through the strap. Please use an anti-static pad when putting down any components or parts or tools outside the computer. You may also use an anti-static bag instead of the pad. Please inquire from your local supplier for additional assistance in finding the necessary anti-static gadgets.
NOTE:
DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC PROTECTIONS.
Chapter 1
General Description
The HS-7238 is an Intel(R) 845GV GMCH/ICH4 chipset-based board designed. The HS-7238 series is ideal all-in-one PCI-ISA Bus single board computer. Additional features include an enhanced I/O with DVI-I/CRT, dual LAN, wireless LAN, audio and USB2.0 interfaces. Its onboard ATA/33/66/100 to IDE drive interface architecture allows the HS-7238 to support data transfers of 33, 66 or 100MB/sec. to one IDE drive connection. The HS-7238 supports all PGA478 Intel(R) Pentium(R) 4 processor up to 2.6GHz. The display controller is Intel(R) 845GV with 1MB or 8MB (default) shared main memory supporting CRT display up to 1920 x 1200 x 32-bit at 60Hz. It also provides DVI display interface. System memory is also sufficient with the one DDR socket that can support up to 1GB. Additional onboard connectors include three internal USB2.0 ports providing faster data transmission. And two external RJ-45 connectors for 10/100 Based Ethernet uses.
1
1.1
Major Features
The HS-7238 comes with the following features:
Intel(R) Pentium(R) 4 processor 2.0A~2.6GHz Supports 400/533MHz FSB One DDR socket with a max. capacity of 1GB Intel(R) 82845GV GMCH/ICH4 chipset Winbond W83627, ITE IT8888 super I/O chipset Intel(R) 82845GV graphics controller Intel(R) 82559 and 82562 dual fast Ethernet controller AC97 3D audio controller Fast PCI ATA/33/66/100 IDE controller 2 COM, 3 USB2.0 ports Hardware Monitor function Wireless LAN module (optional)
2
1.2
Specifications
CPU: Intel(R) Pentium(R) 4 processor 2.0A~2.6GHz Front Side Bus: 400/533MHz FSB Memory: One DDR socket supporting up to 1GB Chipset: Intel(R) 845GV GMCH/ICH4 I/O Chipset: Winbond W83627, ITE IT8888 VGA: Intel(R) 82845GV with 1MB/8MB shared main memory supporting DVI-I/CRT display up to 1920 x 1200 at 32-bit colors (DVI-I and CRT connector is optional) Ethernet: Intel(R) 82562 and 82559 10/100 Based LAN Wireless LAN: Provides wireless LAN module (optional) Audio: AC97 3D audio controller IDE: Two 2.54-pitch 40-pin IDE connectors FDD: Supports up to two floppy disk drives Parallel: One enhanced bi-directional parallel port supporting SPP/ECP/EPP Serial Port: 16C550 UART-compatible RS-232 x 2 serial ports with 16-byte FIFO USB: 3 internal USB2.0 ports Keyboard/Mouse: PS/2 6-pin Mini DIN BIOS: Award PnP Flash BIOS Watchdog Timer: Software programmable time-out intervals from 1~256 sec. CMOS: Battery backup Temperature: 0~60C (operating) Hardware Monitor: Winbond W83627HF Board Size: 18.6(L) x 12.2(W) cm
3
1.3
Board Dimensions
4
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-7238 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures.
2.2
Inspection
After unpacking the board, place it on a raised surface and carefully inspect the board for any damage that might have occurred during shipment. Ground the board and exercise extreme care to prevent damage to the board from static electricity. Integrated circuits will sometimes come out of their sockets during shipment. ExAwardne all integrated circuits, particularly the BIOS, processor, memory modules, ROM-Disk, and keyboard controller chip to ensure that they are firmly seated. The HS-7238 delivery package contains the following items: HS-7238 Board x 1 Utility CD Disk x 1 Cables Package x 1 Cooling Fan & Heat Sink x 1 Jumper Bag x 1 User's Manual It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately.
5
This page is the blank page.
6
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware using the HS-7238. This chapter also contains information related to jumper settings of switch, and watchdog timer selection etc.
3.1
Before Installation
After confirming your package contents, you are now ready to install your hardware. The following are important reminders and steps to take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings and CMOS setup correctly. Refer to the sections on this chapter for the default settings of each jumper. (set JP2 1-2) Go through the connections of all external devices and make sure that they are installed properly and configured correctly within the CMOS setup. Refer to the sections on this chapter for the detailed information on the connectors. Keep the manual and diskette in good condition for future reference and use. Make sure your power supply is using for P4 only. One of 4-pin connectors is for +12V lead which should connect to PW2 connector of HS-7238
2.
3. 4.
NOTE:
Since AD22 has been assigned for ISA bridge at HS-7238, please make sure do not use this address for other PCI cards to avoid confliction. In order to get detailed information, please contact technical support engineer.
7
3.2
Board Layout
8
3.3
JP1 JP2 JP3
Jumper List
Default Setting
System Frequency Select: Auto Clear CMOS: Normal Operation Onboard LAN 2 Enabled/Disabled Select: Enabled
Jumper
Setting
Short 1-2 Short 1-2 Short 1-2
Page
10 16 15
3.4
Connector List
Definition
CD Analog Input Connector Line In Connector Reset Connector Speaker Connector Green LED Connector COM 2/COM 1 Connector (5x2 header) MIC In/Line Out Connector 2-pin ATX Power On/Off Switch HDD LED Connector Dual RJ-45 Connector CRT or DVI-I Connector 6-pin KB/MS Connector DDR Socket Floppy Connector Fan Power In Connector Primary/Secondary IDE Connector PS/2 6-pin Mini DIN KB/MS Connector Parallel Port 20-pin/4-pin ATX Power In Connector USB Ports Mini PCI Connector
Connector
CD1 CD2 CN1 CN2 CN3 CN4/CN5 CN6 CN7 CN8 CN10 CN11 CN12 DM1 FD1 FAN1/FAN2 ID1/ID2 KB1 LP1 PW1/PW2 US1/US2/US3 PC1
Page
20 20 18 18 18 13 20 16 18 15 11 17 11 13 16 12 17 14 16 15 22
9
3.5
Configuring the CPU
The HS-7238 offers the convenience in CPU installation with its auto-detect feature. After installing a new microprocessor onboard, the HS-7238 automatically identifies the frequency and clock speed of the installed microprocessor chip, there by eliminating the need for user to do additional CPU configuration or hardware settings related to it..
JP1: System Frequency Select
Options
Auto Detect (default) 100MHz FSB 133MHz FSB
Settings
1-2 Short 2-3 Short Open
1 3
Heat Sink Installation
Please smear the heat sink paste over CPU and 845GV uniformly. Then secure the heat sink as the picture above. When lock the screw, please DO NOT too tight to locking, if too tight the PCB will be curved, it may cause the board damage.
10
3.6
System Memory
The HS-7238 provides one DDR socket at locations DM1. The maximum capacity of the onboard memory is 1GB.
3.7
VGA Controller
The onboard Intel(R) 845GV with 1MB or 8MB share main memory supports CRT display up to 1920 x 1200 x 32-bit at 60Hz. The HS-7238 provides two methods of connecting VGA device. CN11 offers a single standard CRT connector or DVI-I connector.
CN11: 15-pin CRT Connector
PIN Description PIN Description
1 3 5 7 9 11 13 15 Red Blue GND GND N/C N/C HSYNC SCL 2 4 6 8 10 12 14 Green N/C GND GND GND SDA VSYNC
1 6 11
5 10 15
CN11: DVI-I Connector
PIN Description PIN Description
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 TDC2J GND N/C DDCDATA TDC1J GND N/C GND TEC0GND N/C TLC RED BLUE GND 2 4 6 8 10 12 14 16 18 20 22 24 26 28 TDC2 N/C DDCCLK VSYNC TDC1 N/C VCC5 HPDET TDC0 N/C GND TLC1 GREEN HSYNC
11
3.8
PCI E-IDE Drive Connector
ID1 and ID2 are standard 2.54-pitch 40-pin connector daisy-chain driver connector serves the PCI E-IDE drive. A maximum of four ATA/33/66/100 IDE drives can be connected to the HS-7238 via ID1 and ID2.
ID1/ID2: Primary/Secondary IDE Connector
PIN
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
39 40
Description
Reset DATA 7 DATA 6 DATA 5 DATA 4 DATA 3 DATA 2 DATA 1 DATA 0 GND PDREQ IOW# IOR# PIORDY PDACKInterrupt PDA1PDA0PCS1HDD Active
PIN
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
Description
GND DATA 8 DATA 9 DATA 10 DATA 11 DATA 12 DATA 13 DATA 14 DATA 15 N/C GND GND GND PD1GND N/C PATA66 PDA2PCS3GND
1 2
12
3.9
Floppy Disk Drive Connector
The HS-7238 a standard 34-pin connector, FD1, for floppy disk drive connection. A total of two FDD drives may be connected to FD1 at any given time.
FD1: FDD Connector
PIN Description PIN Description
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 GND GND GND GND GND GND GND GND GND GND GND GND GND GND N/C GND N/C 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 DRVDEN0 N/C DRVDEN1 INDEX# MTR0# DS1# DS0# MTR1# DIR# STEP# WDATA# WGATE# TRAK00# WRTPRT# RDATA# HDSEL# DSKCHG#
1 18
17 34
3.10 Serial Port Connectors
The HS-7238 offers NS16C550 compatible UARTs with Read/ Receive 16-byte FIFO serial ports and internal 10-pin headers.
CN5: COM 1/COM 2 Connector (5x2 Header)
PIN Description PIN Description
1 3 5 7 9 DCD RXD TXD DTR GND 2 4 6 8 10 DSR RTS CTS RI N/C
9 10 1 2
13
3.11 Parallel Port
LP1 is a standard 26-pin flat cable connector designed to accommodate parallel port connection onboard the HS-7238.
LP1: Parallel Port
PIN
1 2 3 4 5 6 7 8 9 10 11 12 13
Description
Strobe DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 Acknowledge Busy Paper Empty Printer Select
13
PIN
14 15 16 17 18 19 20 21 22 23 24 25 26
Description
Auto From Feed ERROR# Initialize Printer Select LN# GND GND GND GND GND GND GND GND GND
1
26
14
14
3.12 Ethernet Connector
The HS-7238 provides two external RJ-45 interface connectors. Please refer to the following for its pin information.
CN10: Dual RJ-45 Connector
PIN
1 2 3 4 5 6 7 8
Description
TX+ TXRX+ R/C GND R/C GND RXR/C GND R/C GND
8
1
JP3: Onboard LAN 2 Enabled/Disabled Select
Options
Enabled (default) Disabled
Settings
Short 1-2 Short 2-3
1 3
3.13 USB Connector
The HS-7238 provides internal USB port at location US1 and US2.
US1: Internal USB Port
PIN
1 2 3 4
Description
VCC BD0BD0+ GND
1
4
US2: Internal USB2.0 Port
PIN
1 3 5 7
Description
VCC BD1BD1+ GND
PIN
2 4 6 8
Description
VCC BD2BD2+ GND
1 7 2 8
15
3.14 CMOS Data Clear
The HS-7238 has a Clear CMOS jumper on JP2.
JP2: Clear CMOS
Options
Normal Operation (default) Clear CMOS
Settings
Short 1-2 Short 2-3
1 3
IMPORTANT: Before you turn on the power of your system, please set JP2 to Short 1-2 for normal operation.
3.15 Power and Fan Connectors
HS-7238 provides one 20-pin and one 4-pin ATX power connectors at PW1 and PW2. HS-7238 must use P4 power supply. One of 4-pin Connector is for +12V lead which should be connected to PW2. 20-pin ATX power in connector can be connected to Backplane or to PW1.
PW1: 20-pin ATX Power In Connector
PIN
1 2 3 4 5 6 7 8 9 10
Description PIN Description
+3.3V +3.3V GND +5V GND +5V GND Power OK 5VSB +12V 11 12 13 14 15 16 17 18 19 20 +3.3V -12V GND PS_ON GND GND GND -5V +5V +5V
11
1
20
10
PW2: 4-pin +12V ATX Power In Connector
PIN
1 2 3 4
Description
GND GND +12V +12V
2
4
1
3
16
CN7: 2-pin ATX Power On/Off Switch
PIN
1 2
Description
Pull 220 to VCCSTBY PANSWIN
1 2
FAN1/FAN2: Fan Power In Connector
PIN
1 2 3
Description
GND +12V Fan In 2
1 3
Connector FN2 onboard HS-7250/HS-7650 series is a 3-pin fan power output connector.
3.16 Keyboard/Mouse Connectors
The HS-7238 offers two methods for keyboard/mouse connections. The connections are done via KB1 for an external PS/2 type keyboard/mouse connection, and CN12 for 6-pin keyboard/mouse header.
KB1: PS/2 6-pin Mini DIN Keyboard/Mouse Connector
PIN
1 2 3 4 5 6
Description
Keyboard Data Mouse Data GND +5V Keyboard Clock Mouse Clock
6 4 2 5 3 1
CN12: 6-pin Keyboard/Mouse Connector
PIN
1 2 3 4 5 6
Description
Keyboard Clock Mouse Data GND +5V Keyboard Clock Mouse Clock
1
6
17
3.17 System Front Panel Control
The HS-7238 has one LED at location CN3 that indicates the system front panel status. This visual feature of the HDD LED may also be connected to and external HDD LED via connector CN8. At location CN1 is reset button.
CN1: Reset Button Connector
PIN
1 2
Description
GND Reset
1 2
CN8: HDD LED Connector
PIN
1 2
Description
Pull 150 to +5V HDD LED
1 2
CN3: Green LED Connector
PIN
1 2
Description
Pull 150 to +5V GND
1 2
3.18 Speaker
Aside from the buzzer at location BZ1, the HS-7238 also offers a connector for an external speaker connection. The table below lists the pin assignments of CN2.
CN2: External Speaker
PIN
1 2 3 4
Description
+5V GND GND Speak In
1
4
18
3.19 Watchdog Timer
Once the Enable cycle is active a Refresh cycle is requested before the time-out period. This restarts counting of the WDT period. When the time counting goes over the period preset of WDT, it will assume that the program operation is abnormal. A system reset signal will restart when such error happens. The following sample programs show how to enable, disable and refresh the watchdog timer:
.286 .MODEL SMALL .DATA x1 copyright x2 port datao db db db ;this is data area
'-------------------------------------------------------',0ah,0dh,'$' '|Copyright by Boser technology write by Richard | ',0ah,0dh,'$' '-------------------------------------------------------',0ah,0dh,'$' 02Eh 02Fh ;W83627H Chipset port ;data port
equ equ
.CODE print macro mov mov int endm buff dx,offset buff; ah,09h 21h
begin
proc near mov ax,@data mov ds,ax STI mov mov out jmp out mov mov out jmp mov mov out jmp mov mov out jmp mov mov out dx,port al,087H dx,al $+2 dx,al dx,port al,07H dx,al $+2 dx,datao al,08H dx,al $+2 dx,port al,030H dx,al $+2 dx,datao al,01H dx,al ; W83627H ; Unlock registor ;
; ; ; set device 8 ;
; Watchdog IO function ; registor
; set 01h toactivate ;
19
jmp mov mov out jmp mov mov out jmp mov mov out jmp mov mov out print print print mov int .stack endp end begin
$+2 dx,port al,0f5H dx,al $+2 dx,datao al,00H dx,al $+2 dx,port al,0f6H dx,al $+2 dx,datao al,05H dx,al ; set CRF5 ;
; set CRF5 to secend ;
; set CRF6 time ;
; set CRF6 time to 5 s' ;
x1 copyright x2 ah,4ch ;go back to dos 21h
begin
User can also use AL, 00H's defined time for reset purposes, e.g. 00H = Disable, 01H = 1sec, 02H=2sec....FFH = 255sec.
3.20 Audio Connectors
The HS-7238 has an onboard AC97 3D audio controller. The following tables list the pin assignments of the Line In/Line Out connector.
CD1: CD-ROM Analog Input Connector
PIN
1 2 3 4
Description
CD_R CD_REF CD_REF CD_L
1
4
CD2: Line In Analog Input Connector
PIN
1 2 3 4
Description
LINE_R GND GND LINE_L
1
4
20
CN6: MIC In/Line Out Connector
PIN Description PIN Description
1 3 5 7 AOUTL GND MIC IN GND 2 4 6 8 AOUTR GND N/C GND
1 7 2 8
21
3.21 Mini PCI Connector
The HS-7238 provides a Type I mini PCI interface which is a very popular notebook computer expansion interface for Modem, Video, LAN, etc. The mini PCI onboard HS-7238 is at location PC1.
22
Chapter 4
Award BIOS Setup
The HS-7238 uses Award BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features.
4.1
Starting Setup
The Award BIOS is immediately activated when you first power on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system. While the BIOS is in control, the Setup program can be activated in one of two ways:
1. By pressing immediately after switching the system on, or 2. By pressing the key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test).
Press DEL to enter SETUP. If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing , , and keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will be asked to... PRESS F1 TO CONTINUE, DEL TO ENTER SETUP
23
4.2
Using Setup
In general, you use the arrow keys to highlight items, press to select, use the and keys to change entries, and press to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard.
Esc key Move to previous item Move to next item Move to previous item Move to previous item Main Menu -- Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Decrease the numeric value or make changes Increase the numeric value or make changes Increase the numeric value or make changes Decrease the numeric value or make changes Reserved Change color from total 8 colors. F2 to select color forward F2 to select color backward Reserved Reserved Reserved Reserved Reserved Reserved Save all the CMOS changes, only for Main Menu
PgUp key PgDn key + key - key F1 key F2 key F3 key F4 key F5 key F6 key F7 key F8 key F9 key F10 key
24
4.3
Main Menu
Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press to enter the sub-menu.
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item
Esc: Quit F9: Menu in BIOS F10: Save & Exit Setup
NOTE:
A brief description of the highlighted choice appears at the bottom of the screen.
25
4.4
Standard CMOS Features
The standard CMOS is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, you must set the HDD mode to LBA mode. Please use the IDE setup utility in BIOS setup to install the HDD correctly.
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
Standard CMOS Features
Date (mm:dd:yy) Time (hh:mm:ss) IDE IDE IDE IDE Primary Master Primary Slave Secondary Master Secondary Slave Mon, Aug 9 2004 10 : 32 : 57 [Auto] [Auto] [Auto] [Auto] [1.44M, 3.5in.] [None] [EGA/VGA] [All, But Keyboard] 640K 252928K 253952K Item Help
Drive A Drive B Video Halt On Base Memory Extended Memory Total Memory
: Select Item F5: Previous Values
+/-/PU/PD: Value
F10: Save
Esc: Quit
F1: General Help
F6: Fail-Safe Defaults
F7: Optimized Defaults
26
4.5
Advanced BIOS Features
This section allows you to configure your system for the basic operation. You have the opportunity to select the system's default speed, boot-up sequence, keyboard operation, shadowing and security.
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
Advanced CMOS Features
Virus Warning CPU L1 & L2 Cache Hyper-Threading Technology Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Boot Up Floppy Seed Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Typematic Rate (Chars/Sec) Typematic Delay (Msec) Security Option APIC Mode MPS Version Control For OS OS Select For DRAM > 64MB Report No FDD For WIN 95 Small Logo(EPA) Show [Disabled] [Enabled] [Enabled] [Enabled] [Floppy] [Hard Disk] [CDROM] [Enabled] [Enabled] [On] [Fast] [Disabled] 6 250 [Setup] [Enabled] [1.4] [Non-OS2] [No] [Enabled] Item Help
: Select Item F5: Previous Values
+/-/PU/PD: Value
F10: Save
Esc: Quit
F1: General Help
F6: Fail-Safe Defaults
F7: Optimized Defaults
27
4.6
Advanced Chipset Features
This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. It must be stated that these items should never be altered. The default settings have been chosen because they provide the best operating conditions for your system. You must consider making any changes only if you discover that the data has been lost while using your system.
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
Advanced Chipset Features
DRAM Timing Selectable CAS Latency Time Active to Precharge Delay DRAM RAS# to CAS# Delay DRAM RAS# to Precharge Turbo Mode Memory Frequency For System BIOS Cacheable Video BIOS Cacheable Memory Hole At 15M-16M Delayed Transaction Delay Prior to Thermal AGP Aperture Size (MB) ** ON-chip VGA Setting ** On-chip VGA On-chip Frame Buffer size [By PSD] [1.5] [7] [3] [3] [Disabled] [Auto] [Enabled] [Enabled] [Disabled] [Enabled] [16 Min] [64] [Enabled] [8MB] Item Help
: Select Item F5: Previous Values
+/-/PU/PD: Value
F10: Save
Esc: Quit
F1: General Help
F6: Fail-Safe Defaults
F7: Optimized Defaults
28
4.7
Integrated Peripherals
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
Integrated Peripherals
On-Chip Primary PCI IDE IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA On-Chip Secondary PCI IDE IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA IDE Secondary Slave UDMA USB Controller USB 2.0 Controller USB Keyboard Support USB Mouse Support AC97 Audio Init Display First IDE HDD Block Mode POWER ON Function KB Power ON Password Hot Key Power On Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select RxD, TxD Active IR Transmission Delay UR2 Duplex Mode Use IR Pins Onboard Parallel Port Parallel Port Mode EPP Mode Select ECP Mode Use DMA POWER After PWR-Rail
: Select Item F5: Previous Values
[Enabled] [Auto] [Auto] [Auto] [Auto] [Enabled] [Auto] [Auto] [Auto] [Auto] [Enabled] [Enabled] [Enabled] [Enabled] [Auto] [Onboard/AGP] [Enabled] [BUTTON ONLY] [Enter] [Ctrl-F1] [Enabled] [3F8/IRQ4] [2F8/IRQ3] [Normal] [Hi, Lo] [Enabled] [Half] [IR-Rx2Rx2] [378/IRQ7] [SPP] [EPP1.7] [3] [Off]
F10: Save Esc: Quit
Item Help
+/-/PU/PD: Value
F1: General Help
F6: Fail-Safe Defaults
F7: Optimized Defaults
29
4.8
Power Management Setup
The power management setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his owns style of computer use.
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
Power Management Setup
ACPI Function ACPI Suspend Type Run VGABIOS If S3 Resume Power Management Video Off Method Video Off In Suspend Suspend Type MODEM Use IRQ Suspend Mode HDD Power Down Soft-Off by PWR-BTTN CPU THRM-Throttling Wake-Up by PCI Card Power On by Ring Wake Up On LAN USB KB Wake-Up From S3 Resume by Alarm Date(of Month) Alarm Time(hh:mm:ss) Alarm ** Reload Global Timer Events ** Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD, COM, LTP Port PCI PIRQ[A-D]# [Enabled] [S1(POS)] Auto [User Define] [DPMS] [Yes] [Stop Grant] [3] [Disabled] [Disabled] [Instant-Off] [50.0%] [Disabled] [Disabled] [Disabled] Disabled [Disabled] 0 0:0:0 [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled]
F10: Save Esc: Quit F1: General Help
Item Help
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F7: Optimized Defaults
30
4.9
PnP/PCI Configurations
This section describes the configuration of the PCI bus system. Peripheral Components Interconnect (PCI), is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
PnP/PCI Configurations
PNP OS Installed Reset Configuration Date Resources controlled By IRQ Resources DMA Resources IRQ-3 Assigned to IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 PCI/VGA Palette Snoop
: Select Item F5: Previous Values
[No] [Disabled] [Auto(ESCD)] Press Enter Press Enter PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device [Disabled]
F10: Save Esc: Quit
Item Help
+/-/PU/PD: Value
F1: General Help
F6: Fail-Safe Defaults
F7: Optimized Defaults
31
4.10 PC Health Status
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
PC Health Status
CPU Warning Temperature Current System Temp Current CPU Temperature Current CPUFAN Speed Current SYSTEM FAN Speed VCORE +3.3V +5V +12V -12V -5V VBAT(V) 5VSB(V) Shutdown Temperature
: Select Item F5: Previous Values
[Disabled]
Item Help
[Disabled]
F10: Save Esc: Quit F1: General Help
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F7: Optimized Defaults
4.11 Frequency/Voltage Control
CMOS Setup Utility - Copyright(c) 1984-2001 Award Software
Frequency/Voltage Control
CPU Clock Ratio Auto Detect PCI Clk Spread Specturm [8x] [Enabled] [Disabled] Item Help
: Select Item F5: Previous Values
+/-/PU/PD: Value
F10: Save
Esc: Quit
F1: General Help
F6: Fail-Safe Defaults
F7: Optimized Defaults
32
Chapter 5
Software Utilities
This chapter contains the detailed information of IDE, VGA, LAN, audio and USB2.0 driver installation procedures. The utility disk that comes with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA, LAN and Audio drivers. The following sections describe the installation procedures of each driver based on Win 95/98, Win 2000 and Win NT operating systems. It is recommended that you install the drivers matching the sections listed in this chapter.
5.1
1.
IDE Driver Installation
Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the HS-7238 button to launch the installation program.
33
2.
Click on the ICH4 Driver button to continue.
3.
Immediately after clicking the IDE button in Step 1, the program launches the Setup that will assist you in the installation process. Click on the Next > button to proceed.
34
4.
The License Agreement dialog box then appears on the screen. Choose Yes to proceed.
5.
When the Readme Information dialog box pops up , just click on the Next > button to proceed.
35
6.
Once the Install Shield Wizard finishes updating your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot. Only after your computer boots will the new settings take effect.
NOTE: WIN98/2K/XP IDE driver installations are the same.
36
5.2
1.
VGA Driver Installation
Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the HS-7238 button to launch the installation program.
5.2.1 WIN98
2.
Click on the VGA Driver button to continue.
37
3.
Click on the WIN9X button to continue.
4.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
38
5.
The Intel(R) OEM Software License Agreement dialog box the n appears on the screen. Choose Yes to proceed.
6.
Once the setup program finishes copying files into your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot. Only after your computer boots will the new settings take effect.
39
5.2.2 WIN NT
NOTE: Please make sure you have already installed Service Pack 6.0.
1. Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the HS-7238 button to launch the installation program.
2.
Click on the VGA Driver button to continue.
40
3.
Click on the WINNT button to continue.
4.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
41
5.
The Intel(R) OEM Software License Agreement dialog box then appears on the screen. Choose Yes to proceed.
6.
Once the setup program finishes copying files into your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot.
42
5.2.3 WIN2000/WINXP
1. Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the HS-7238 button to launch the installation program.
2.
Click on the VGA Driver button to continue.
43
3.
Click on the WIN2K button to continue.
4.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
44
5.
The Intel(R) OEM Software License Agreement dialog box appears on the screen. Choose Yes to proceed.
6.
Once the setup program finishes copying files into your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot. Only after your computer boots will the new settings take effect.
45
5.3
1.
LAN Driver Installation
Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the HS-7238 button to launch the installation program.
5.3.1 WIN98
2.
Click on the LAN Driver button to continue.
46
3.
Click on the WIN9X button to continue.
4.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
47
5.
The Intel(R) OEM Software License Agreement dialog box then appears on the screen. Choose Next > to proceed.
6.
The Setup Type dialog box then appears on the screen. Choose Typical to proceed.
48
7.
When the dialog box below appears, make sure you close all other Windows applications then click on the Install button to proceed.
8.
When the dialog box below appears, it means your driver is install completed. Click Finish button to proceed.
49
9.
Once the setup program finishes copying files into your system, will prompt you to restart the computer. Tick on the Yes to reboot. Only after your computer boots will the new settings take effect.
5.3.2 WINNT
NOTE: Please make sure you have already installed Service Pack 6.0.
1. The system automatically detects the absence of Windows NT Networking. Click on the Yes button to start installation.
2.
Tick on the Wired to the network once the following screen appears. Click on the Next > to proceed.
50
3.
Click on the Start Search button for the program to locate the Network Adapter.
4.
Once setup finishes the search, it will list a number of adapters for you to choose from. Press on the Have Disk button to assign the driver path location.
5.
Setup now asks you for the location of the driver. When you have entered the new driver path, press on the OK button to continue.
51
6.
When Setup finds the information it needs about the new driver, it will display the device it found on the following screen. If using 82551 or 82562, please choose "Intel(R) PRO/100 Family
Adapter". If using 82540EM, please choose "Intel(R) PRO/1000 Family Adapter". Press on the OK button to accept and proceed.
7.
Setup then returns to Network Setup Wizard screen and displays your new Network Adapter. Click on Next > to continue.
52
8.
The Network Setup Wizard then allows you to set the Network Protocols on your network. Select the appropriate protocol and then click on Next > to continue.
9.
Before Setup starts installing the components found and the settings you made, it will give you the option to proceed or go back for changes from the following screen. Click on the Next > button once you are sure of your devices.
53
10.
Windows NT Setup will then need to copy files necessary to update the system information. Specify the path then press Continue.
11.
When Setup asks if you wish to change the TCP/IP settings of your system, select them appropriately. The default choice is No.
12. 13.
Setup then starts the Networking installation and copies the files. When the screen below appears, click on Next > to continue.
54
14.
Setup then prompts you that it is ready to start the network. You may complete the installation thereafter. Click on Next > to continue.
15.
Assign the workgroup or domain setting of your computer. Click on Next > to continue.
55
16.
When the dialog box below appears, it means your driver is install completed. Click Finish button to proceed.
17.
Click on the Yes button to restart your computer. The LAN driver installation for WINNT is now complete.
56
5.4
1.
Audio Driver Installation
Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the HS-7238 button to launch the installation program.
2.
Click on the Audio Driver button to continue.
57
3.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
4.
Once the Install Shield Wizard completes the operation and update of your AC97 driver, it will ask you to remove disks form their drives, and prompt you to restart your system. Tick on the Yes, I want to restart my computer now. Afterwards, click on the Finish button to complete the installation process. The system changes you made will take effect after the system restarts.
58
5.5
1.
USB2.0 Driver Installation
With the Utility CD Disk still in your CD-ROM drive, right click on "My Computer" icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu.
5.5.1 WIN98
2.
Select on Other Devices from the list of devices then double-click on PCI Universal Serial Bus.
59
3.
The PCI Universal Serial Bus Properties screen then appears, allowing you to reinstall the driver. Select Driver from the main menu to proceed.
4.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
60
5.
Tick on the "Search for a better driver" once the following screen appears, Click on the Next > to proceed.
6.
Once the program returns to the Add New Hardware Wizard screen, your specified location will appear. Press on the Next > button to continue.
61
7.
When Setup finds the information it needs about the new driver, it will display the device it found on the following screen. Press on the Next > button to accept and proceed.
8.
Once the Install Shield Wizard completes the operation and update of your USB2.0 driver. Click on the Finish button to complete the installation process.
62
5.5.2 WIN2K
1. With the Utility CD Disk still in your CD-ROM drive, right click on "My Computer" icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu. Select on Other Devices from the list of devices then double-click on PCI Universal Serial Bus.
2.
3.
The PCI Universal Serial Bus Properties screen then appears, allowing you to reinstall the driver. Select Driver from the main menu to proceed.
63
4.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
5.
Tick on the "Search for a better driver" once the following screen appears, Click on the Next > to proceed.
64
6.
Once the program returns to the Add New Hardware Wizard screen, your specified location will appear. Press on the Next > button to continue.
7.
Choose the driver disk location.
65
8.
Once the Install Shield Wizard completes the operation and update of your USB2.0 driver. Click on the Finish button to complete the installation process.
5.5.3 WINXP
1. Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the HS-7238 button to launch the installation program.
66
2.
Click on the USB2.0 Driver button to continue.
3.
Click on the WINXP button to continue.
67
4.
When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
5.
Once the Install Shield Wizard completes the operation and update of your USB2.0 driver. Click on the Finish button to complete the installation process.
68

▲Up To Search▲

Price & Availability of HS-7238

	To Download HS-7238 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .